4438成人网_年轻的朋友4韩剧在线观看_亚洲乱码一二三四区_四虎影视最新网站_韩国三级大全久久网站_偷妻无码一区二区三区动漫

Welcome to Jiangxi Bairui Calcium Carbonate Co., Ltd. website!
中文 | EN | Service Tel: +86-795-5288016

Science | sealant performance needs to choose different kinds of calcium carbonate

Time: 2019-10-08

01 Appearance

The appearance of the sealant mainly depends on the dispersion of the filler in the base adhesive. Filler is a kind of solid powder, after the kneading machine, grinder, planetary machine dispersion, it can be evenly dispersed in the base glue to form a delicate paste, sometimes according to the nature of the filler itself is different, does not exclude the existence of a very small amount of slight fine particles or sand, which is acceptable normal phenomenon. If the filler is not well dispersed, there will be a lot of very coarse particles. In addition to the dispersion of the filler, some other factors will also affect the appearance of the product, such as mixed particle impurities, crust and so on. These cases would be considered coarse in appearance. The observation method of appearance is to directly observe the product from the packaging, or to hit the product 1-2g on the white paper, fold the white paper flat and then open the observation, the term is called "butterfly observation". Coarse particles should be judged when found.

02 Hardness

Hardness refers to the hardness of the sealant after it is completely cured into the rubber body, which is one of the physical and mechanical properties of the product. Hardness refers to the ability of a material to resist attempts to carve or press into its surface. According to the different hardness measurement methods, hardness expression methods have Brinell hardness, Rockwell hardness, Shore hardness and other methods. Shore A hardness is stipulated by the state. The standard hardness value is detected by the hardness tester according to the national standard method. The hardness of the sealant is high, the surface sealant is rigid, and the elasticity and flexibility are insufficient; Small hardness is the opposite, elasticity and flexibility are good, rigidity is insufficient. Therefore, the sealant is neither the harder the better, nor the softer the better, but according to the actual needs of a certain range of requirements.

03 Tensile Strength

Tensile strength is also one of the mechanical properties of the sealant after it is fully cured. Tensile strength is also known as tensile strength, tearing strength, commonly known as tension. The ability of a material to resist damage when subjected to tension. The tensile strength value is also detected according to the method specified in the national standard. Sealant according to the needs of its use is to have a certain strength requirements, especially structural adhesive, it is clearly stipulated in the national standard of the minimum value of strength, strength is too poor sealant can not meet the needs of use. However, if too much emphasis on the strength of the sealant and ignore the elasticity is not enterprising.

01 Mechanical properties of sealant under standard conditions

The tensile strength and elongation at break of the sealant prepared by nano-calcium carbonate are close to each other. Nano calcium carbonate, the particle size of about 50nm, large specific surface area, and the sealant polymer in the system of contact points (reinforcing points) more, can form a strong interaction between the molecular interface of the sealant, to prevent crack expansion, shear bands, energy absorption and other effects, so that the tensile strength and elongation of the sealant become larger, so as to have better toughness and impact tear resistance;

The tensile strength and elongation at break of the sealant made of light calcium carbonate are close to each other.

It belongs to micron level active light calcium powder, the specific surface area is lower than nano-calcium carbonate, and other properties are close to nano-calcium carbonate, so the reinforcement point is less than nano-calcium carbonate, and the reinforcement effect is slightly worse;

The tensile strength and elongation at break of the sealant made of heavy calcium carbonate are close to each other.

Is the active heavy calcium powder, the specific surface area is much smaller than nano calcium carbonate and active light calcium carbonate, the number of reinforcing points is the least, so the tensile strength and elongation at break are the lowest, and the reinforcing effect is the worst.

02 Mechanical properties of sealant at 90℃

After 90℃ high temperature treatment, the tensile strength and elongation at break of the sealant are significantly reduced. Among them, the strength and elongation of the sealant made of nano-calcium carbonate decreased most obviously. This is because the specific surface area of nano-calcium carbonate is large, and the heating area is large, and its reinforcing effect is more susceptible to high temperature treatment.

  
Contact us

Address: No. 33, Minzhu Road, Gaoan City, Jiangxi Province, China
Domestic Hotline: 0795-5288016/5288026
International Hotline: +86-795-5288079
Fax: 0795-5219969

Copyright(C)2023, Jiangxi Bairui Calcium Carbonate Co., Ltd. All Rights Reserved. Supported by  ChemNet ChinaChemNet Toocle
主站蜘蛛池模板: 911亚洲精品国内自产 | 亚洲av无码专区国产不乱码 | 国产精品久久久综合久尹人久久9 | 日本高清视频在线WWW色 | 国产激情性色视频在线观看 | 国产成人青青热久免费精品 | 亚洲激情视频 | 天堂va蜜桃一区 | 亚洲国产三级 | 色婷婷夜夜躁狠狠躁麻豆免费 | 日韩欧美一区二区三区不卡在线 | 无码国产精品人妻一区二区 | 夜夜操天天 | 爱久久av一区二区三区 | 久久字幕精品一区 | 好看的日韩精品视频在线 | 激情综合色五月丁香六月亚洲 | 国产成人一区二区视频免费 | 久久一级片 | 成人免费淫片视频观 | 欧美福利视频 | 麻豆文化传媒www网站入口 | 国产精品一区二区AV不卡 | 久久99精品久久久久国产越南 | 欧美日韩国产这里只有精品 | 精品国产乱码久久久久久1区2匹 | 中文字幕av一区二区三区免费看 | 国产社区精品视频 | 欧美人体视频一区二区三区 | 在线免费观看视频a | 中国丰满少妇熟乱xxxx | wwww.国产 | 精品中文av| 亚洲爱爱片| 日产精品久久久一区二区福利 | 成年人精品视频在线观看 | 毛片a级片| 成年女人免费又黄又爽视频 | 日本三极片 | 91精品婷婷色在线观看 | 国产精品久久久久毛片软件 |